How do you change a serpentine belt on a 2014 Kia Sorento? (video)

https://www.youtube.com/watch?v=JFwkQm6Uhm8

How do you change a belt on a Kia Sorento? (video)

https://www.youtube.com/watch?v=UO8Nx4gAaSo

How do you put a serpentine belt on a 2011 Kia Optima?

Release the tensioner pulley when the serpentine belt is removed. Remove the belt from the water pump and crankshaft. Turn the crankshaft pulley using a 22mm wrench and as you move the pulley remove the belt. Get the new belt, line it up back to the pulley, and twist the crankshaft to install the new belt. via

How do you change a serpentine belt on a 2008 Kia Sportage? (video)

https://www.youtube.com/watch?v=a3h9gUU8Pfg

How do you change a serpentine belt on a 2007 Kia Rondo? (video)

https://www.youtube.com/watch?v=DZvVwUIVX20

How do you change a serpentine belt on a 2016 Kia Optima? (video)

https://www.youtube.com/watch?v=te_872LH28Q

Can I change my serpentine belt myself?

Replacing the serpentine belt is as simple as threading it into position, cranking the tensioner and slipping the belt over the tensioner pulley, or nearest pulley up top. Belt tensioners are mostly spring tension. Once installed, the spring retains pressure to the belt. via

How do you put a two ring belt on? (video)

https://www.youtube.com/watch?v=OcqjGl4QjVU

What causes drive belt misalignment?

Serpentine belt misalignment can be caused by any of the accessory pulleys. Or, it may be the result of improper belt installation. There are two types of misalignment, each caused by the relationship of the pulleys to one another. via

What noise will a belt make if the pulley is misaligned?

A chirping noise that increases in frequency as the engine is revved up can be the result of belt vibration caused by misaligned pulleys. In fact most cases of belt noise are caused by misaligned pulleys and belts. via

What happens if pulleys are not aligned?

When pulleys are not aligned properly, additional loads are induced. The aim of belt alignment is to align the grooves of the drive and driven pulleys so that the belts run with minimal wear. Proper alignment extends the service life of belts and bearings, reduces vibration and noise levels, and saves energy. via

How do you line up a pulley on an engine? (video)

https://www.youtube.com/watch?v=BzMnc3FCtdI

How do you align a pulley with a string? (video)

https://www.youtube.com/watch?v=KvWldO3Zlww

How do I know if my pulley is aligned? (video)

https://www.youtube.com/watch?v=a5HzocYbKSQ

How tight should belt be on alternator? (video)

https://www.youtube.com/watch?v=9RAUtE2aztk

What is the most common cause of belt slippage?

Improper belt tension is the most common and obvious cause of slip, which generates unwanted heat. The friction that occurs when a V-belt slips in a pulley causes belt sidewalls to become glazed, and decreases gripping ability. via

What can happen if the belt tension in a belt drive system is adjusted to be too tight?

If a belt is too tight in a system, it can add stress to your bearings. The added stress to bearings can result into over amperage of your motor and potential motor failure. via

Which direction do women's belts go? (video)

https://www.youtube.com/watch?v=Ej74R-IiSPY

How should a belt fit?

Please remember that the belt is sized correctly when you can wear the pin of the buckle through the middle hole. Good quality belts usually have 5 holes. You should then be able to wear the pin of the buckle in the third (middle) hole. The belt's tail size will then be automatically in the right proportion. via

How do you buckle a belt? (video)

https://www.youtube.com/watch?v=-8Eqa_T3-IA